-40%
10DOF I2C/SPI MPU9250 BMP280 GY-91 BME280 Kompass Barom for Arduino Raspberry Pi
$ 4.71
- Description
- Size Guide
Description
HomeArduino
Module
Sensor
Chips
About Us
BMP280
Druckbereich: 300-1100 hPa (9000 Meter über dem Meeresspiegel auf -500m)
Relative Genauigkeit (bei 950 - 1050 hPa bei 25°C): ±0.12 hPa, equiv. zu ±1 m
Absolute Genauigkeit (bei (950 - 1050 hPa, 0 - +40 °C): ±0.12 hPa, equiv. zu ±1 m
Netzspannung: 1,8 V - 3,6 V
Stromverbrauch: 2,7µA bei 1Hz Ausleserate
Temperaturbereich: -40 bis +85°C
Package included:
1x BMP280 Sensor Bord inklusive Stiftleiste
BMP280 MPU9250
Chip: MPU-9250 + BMP280
Power supply: 3-5v (internal low dropout regulator)
Communication: standard IIC / SPI communications protocol
Chip built 16bit AD converter, 16-bit data output
Gyroscopes range: ± 250 500 1000 2000 ° / s
Acceleration range: ± 2 ± 4 ± 8 ± 16g
Magnetic field range: ± 4800uT
Pressure range: 300-1100hPa
Using Immersion Gold PCB, machine welding process to ensure quality
2.54mm pin pitch
Module size:(L*W)2.05* 1.43cm/0.81"*0.56"
Package Included:1x MPU9250 BMP280 10DOF Acceleration Gyroscope Compass Nine Shaft GY-91 Sensor
GY-BME280-3.3V
ME-BME280 is a Breakout Board featuring a Sensortec ME280 Temperature, Humidity & Pressure Sensor.
The board has selectable I2C address jumper (solder link GS2), I2C pull-up resistors, 7 pin header 2.54mm, and two mounting holes 3.5mm.
Default setting of the board; single power rail Vdd=Vdd_IO (solder link GS1), pull-ups resistors (R2, R3) 10k, protocol selector resistor 0ohm (R1), decoupling capacitors 0.1uF on both power supply pins Vdd & Vdd_IO.
If you connect board to both power rails VDD_IO 1.8V and VDD 3.3V be sure to remove the power rail jumper GS1!
BME280 Features
Package 2.5 mm x 2.5 mm x 0.93 mm metal lid LGA
Digital interface I2C (up to 3.4 MHz) and SPI (3 and 4 wire, up to 10 MHz)
Supply voltage VDD main supply voltage range: 1.71 V to 3.6 V
VDDIO interface voltage range: 1.2 V to 3.6 V
Current consumption 1.8 uA @ 1 Hz humidity and temperature
2.8 uA @ 1 Hz pressure and temperature
3.6 uA @ 1 Hz humidity, pressure and temperature
0.1 uA in sleep mode
Operating range -40…+85 C, 0…100 % rel. humidity, 300…1100 hPa- Humidity sensor and pressure sensor can be independently enabled/disabled
Package Included:
1PCS I2C/SPI Breakout Temperature Humidity Barometric Pressure BME280 Digital Sensor
GY-BME280-5V
BME280, the precision sensor from It, is soldered onto PCB.
Not only the pressure and the temperature, this sensor can measure humidity.
It uses both I2C and SPI (supports 3-, 4-wire SPI) interface
Specifications:
Supply Voltage: 1.8 - 5V DC
Interface: I2C (up to 3.4MHz), SPI (up to 10 MHz)
Operational Range:
Temperature: -40 to +85°C
Humidity: 0-100%
Pressure: 300-1100 hPa
Resolution:
Temperature: 0.01°C
Humidity: 0.008%
Pressure: 0.18Pa
Accuracy:
Temperature: +-1°C
Humidity: +-3%
Pressure: +-1Pa
I2C address
SDO LOW : 0x76
SDO HIGH: 0x77
Package Included:
1 x Breakout Temperature Humidity Barometric Pressure BME280 Digital Sensor Modul
Payment
Shipping
Refund
Payment
We accept PayPal only.
But we only
Accept
your
Ebay Address
,Please Make sure it's 100% right.
Payment must be received in 5 business days of auction closing.
Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
Shipping
Fill your shipping info
Refund
All package need to
wait 30 days
(US only n
eed 7-10 days)
,
Please take care it.Less than 30 days,we can't take a refund
.
If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please contact us and double check the return address before you return it.
If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.